Hello Zhang Li,
Thank you for your message. The REALCAP and CAPTURE software modules were
created for capturing analog video from a computer controlled VCR in an
older version of APAS software. WE have many users that are still using
that hardware and that is why the software modules are still included in the
download. You will not require these programs for video capture.
You should use the Pinnacle software to capture both the Digital Video and
the Analog Video. Just be certain that the video is saved in Microsoft
compatible AVI format. Also, do not perform any tasks other than capturing
the "raw" video. The Studio software allows you to select
options such as
"Make Movie" and we do NOT want to use this since this changes the
timing in
the files. Just capture the desired video and then exit the program.
After capturing the video, the following steps are usually performed in a
typical analysis:
TRIM module - used to "clip" and synchronize the
desired video for
analysis.
DIGITIZE module - used to digitize the individual camera
views. Up to 6
views can be digitized simultaneously.
TRANSFORM module - used to convert the digitized point
locations into
spatial coordinates
FILTER module - used to remove any random digitizing errors
DISPLAY or APASVIEW modules - used to display the results for
analysis.
I hope this helps to answer your questions. Please do not hesitate to
contact me for any further information.
Sincerely,
John Probe
Ariel Dynamics, Inc.
Email: ARIEL1@ix.netcom.com
----- Original Message -----
From: "Zhang Li" <beijingsportdev@hotmail.com>
To: <ariel1@ix.netcom.com>
Sent: Tuesday, November 19, 2002 6:36 AM
Subject: Problem capturing video
>
>
> Dear Mr John Probe,
> We are trying to capturing video using the JVC DVL9800 digital camera
> through the Pinnacle Studio Deluxe Analog and Digital Frame Grabber Card.
> In the RealCap Module, it only shows a black screen. I had checked that
> under Video Source, under Select a Video device "MicroSoft DV Camera
and
> VCR" is selected.
> Under Capture Preferences, Device "Microsoft WDM Image Capture"
is
selected
> and Frame rate "PAL(50 images/sec)" is selected.
> I tried to use the Capture Module, it also show a black screen.
> I checked the Video Source, "MicroSoft DV Camera and VCR" is
selected.
> Also, I had installed the Studio software in the computer. Using the
> Pinnacle software, I am to see and capture the video images using the
analog
> and the digital inputs.
> Could you advise why I can't use the Ariel modules to see and capture the
> video images?
> Regards,
> Zhang Li
> BeiJing Sports Develope Co.
>
>
>
>
> _________________________________________________________________
> Add photos to your messages with MSN 8. Get 2 months FREE*.
> http://join.msn.com/?page=features/featuredemail
>
Hello Olivier,
We are currently using the STUDIO DV capture board made by Pinnacle
Systems. However, any frame grabber that is IEEE 1394 "FireWire"
compatible should work with the JVC camera.
The STUDIO DV board includes capturing software, however, the
"high-speed"
video has to be extracted into single images. JVC accomplishes the
"high-speed" by slitting the full size image into either half or
quarter
size. I have attached a description that helps to explain this process.
This is written for NTSC format, but the same principle applies to the PAL
version cameras.
The Ariel Software Drivers for the JVC camera are required to access the
100 and 200 Hz video. These software drivers are NOT included in the Basic
APAS software and would have to be purchased separately at a cost of
$3,500.00 USD. NOTE: Also it is recommended to use the SP mode (not
LP
mode) for recordings.
I hope this helps to answer your questions.
Sincerely,
John Probe
Email: ARIEL1@ix.netcom.com
At 07:11 PM 12/02/2000 +0100, you wrote:
>hi john,
>thank you for your answer;
>
>>If the JVC-9700 camera supports the "high-speed" video mode,
then you will
>>require additional software to access the high speed options. The
>>standard mode should work just fine.
>
>yes, the JVC-9700 camera supports the "high-speed" video mode (100
and 200
>frames/sec in PAL);
>so what is the best product and model to use with APAS for high-speed video
>capture including this additional software (i think it can extract each
>half frame per image!);
>
>thanks
>olivier
>
>_____________________________________________________
>Olivier MARTIN (olivier.martin@ujf-grenoble.fr)
>UFRAPS - Universite Joseph Fourier - BP53
>38041 GRENOBLE Cedex 09 - FRANCE
>tel. int + (0)4 76 51 41 95 (secr.) / 41 99 (lab.) / 41 89 (perso.)
>fax. int + (0)4 76 51 44 69